A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
Everyone maintains their own opinions about A Step-by-Step Guide to Installing a Bathtub.
Mounting a bathtub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately hard job. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open up a wall to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old bathtub and set in the new one. Make certain you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is far better to take into consideration using one prior to you start. Possibilities are you might need a professional plumber to make tube links.
This write-up will certainly help you set up a brand-new tub in your shower room if you have actually already purchased a new tub as well as do not need to alter the arrangement of your previous water supply pipes.
Your tools as well as material checklist should make up the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited accessibility that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have actually been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap and the sink. Secure the tap in position with the manufacturer provided backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former kind should be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bath tub
Utilizing both wood boards under its feet, put the bath tub in the needed placement. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small points.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit all-time low of the outermost versatile faucet connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water system as well as check all joints and brand-new pipework for leaks and tighten them if needed. Load the bath tub and additionally examine the overflow outlet and also the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and also sealing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will settle it into its final setting.
Planning for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be fitted in its last position.
Tiling Around the Tub
In the area where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to crack a rigid seal, causing the water to penetrate the wall surface in between the bath and the tiling, bring about difficulties with moisture and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, as well as are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is recommended to fit the floor tiles utilizing waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was brought to that report about Tools You Need to Install a New Bathtub from a good friend on our other site. Be sure to take the opportunity to promote this blog posting if you enjoyed reading it. Thanks for your time. Please visit our website back soon.
Excellence awaits, dial! Report this page